dfpasob.blogg.se - Ford ids software hack

#FORD IDS SOFTWARE HACK CODE#

Non-Volatile Memory (NVM) configuration failure – No PCM ID stored in PATS Particial detection of encoded ignition key.

Unprogrammed encoded ignition key detected (leave ignition on for 20 seconds before trying a programmed key, in Anti-Scan Mode) Replace transceiver.ĮCU is defective (EEPROM in PCM is not working – replace PCM). Less than 2 (or 3 if equipped w/Valet key) keys programmed to the system. ABS PATS pairing happens either during PCM - BCM (IPC) pairing, or there is a separate coding procedure available in BCM. In that case to re-code changed ABS, it must be paired as well. Some vehicles have also ABS involved in PATS system. PATS pairing function is now available also on UDS protocol. PATS pairing requires obtaining two INCODE/OUTCODE pairs of both ECUs involved in PATS system. The function is available only on coded PATS. For this purpose FCOM provides “PATS Pairing” function, which is available coding menu of non-PCM ECU (IPC, BCM, SCIL or RKE). PCM and IPC, BCM RKE or SCIL), ECUs need to contain same vehicle security data.

Check if operation was successful by function Information about PATS stateįor vehicles that use multiple ECUs for PATS system (e.g.

Once the information “After clicking Cancel, key will be programmed” appear, insert new key in to ignition OFF (if key have not been there yet) and switch to ON position.

Connect to ECU that holds programmed keys (typ.

If you fail to correctly program keys after running Erase keys procedure, you can try to add keys one-by-one using function "Program (add) a new key".

#FORD IDS SOFTWARE HACK CODE#

Fault code memory will show error stating that less than minimum required keys is programmed.

Check by PATS state information function if the keys was deleted and the new keys added (if the number of keys is 0 or 1, it is necessary to add the next key(s) by Program new key function)Īs long as minimal number of keys required by PCM isn't programmed, engine may not start.

Turn OFF the ignition and wait 60 seconds.

Insert the next key and turn the ignition ON (PATS LED off after about 5 seconds).

Turn ignition ON (wait about 5 seconds), PATS LED is on.

The following procedure is intended for vehicles requiring min. Pressing Cancel button is going to delete ALL keys and is necessary to coding a new one. The control unit is now ready to perform deleting and coding a new keys.

After few minutes of waiting is showing the call for delete keys by pressing Cancel button.

If you are changing key, ignition must not be switched off for more than 10 seconds.Ĭlears all coded keys and programs 2 new keys. Then press Cancel button to start coding procedure. Operations are described in following chapters. While FCOM is waiting for control unit to unlock, it communicates with control unit and therefore ignition has to be switched ON.Ī dialog waiting for the completion of the operation (programming, clearing, etc.) is displayed afterwards. You can cancel the running countdown by clicking on Cancel button. Program cannot speed-up the countdown, it fully depends on the control unit. Timed PATS starts the countdown automatically. For such vehicles you need to obtain the INCODE using other source such as Ford ETIS.

Please note that service doesn't support yet a 2011+ Ford Mondeo/S-Max/Galaxy/Focus and C-Max vehicles that use different system. INCODE can be obtained at or using Ford ETIS service. Using one and the same INCODE during more operations with PATS is not possible. The PATS Login is used only for test purposes (to verify correctness of incode) and some special operations.įor each OUTCODE, which control unit generates, is necessary to get a unique INCODE. PATS unlocking is performed before any operation automatically, you do not have to use FCOM “PATS Login” function. The coded PATS generates a so-called OUTCODE, which requires a so-called INCODE, which is dependent on a specific vehicle and generated OUTCODE. In coding access you see window asking for OUTCODE/INCODE. It is very important to have correct type of transponder for every model and minimal number of keys.īefore any operation with PATS you have to get access to PATS ECU. Number should be equal to or greater than previous value, in other case trouble codes will appear fault code memory. Number of coded keys: Current number of programmed keys. Minimum number of keys: Minimum number of programmed keys required for correct function of PATS (car won't start if less then required number of keys is programmed). 10 minutes is required before codingĬoded: Requires challenge-response INCODE/OUTCODE authorization (you can obtain INCODEs using or through Ford ETIS service) Informs, whether secure access is permitted or forbidden (PATS operations are allowed). This function displays all important information about PATS system and its state. When Anti-scan mode is activated, you must wait at least 30 seconds before any operations with PATS.